Register now or log in to join your professional community.
An overheated engine can be caused by anything that decreases the cooling system’s ability to absorb, transport and dissipate heat; therefore engines can overheat for a variety of reasons. Let’s take a look at some of the most common causes.
Cooling System LeaksThis is the primary cause of engine overheating. Possible leak points include hoses, the radiator, water pump, thermostat housing, heater core, head gasket, freeze plugs, automatic transmission oil cooler, cylinder heads and block. Perform a pressure test. A leak-free system should hold pressure for at least one minute.
Wrong Coolant ConcentrationBe sure to use the coolant recommended by your vehicle’s manufacturer. The wrong type of coolant and/or mixing the incorrect concentration of coolant and distilled water can also result in engine overheating. The best bet is to perform a complete flush and fill.
Bad ThermostatA thermostat is a heat-sensitive valve that opens and closes in response to engine temperature. Heated engine coolant passes through to the radiator when the thermostat is in the open position. In the closed position, it prevents the flow of coolant to speed up the warming of a cold engine. When the thermostat gets stuck in the closed position, coolant stays in the engine and quickly becomes overheated, resulting in engine overheating.
Blocked Coolant PassagewaysRust, dirt and sediment can all block or greatly impede the flow of coolant through the cooling system. This can limit the system’s ability to control engine temperature, which may result in higher operating temperatures and engine overheating. Once again, a flush and fill is recommended to remove debris.
Faulty RadiatorBy passing through a series of tubes and fins, coolant temperature is reduced in the radiator. Leaks and clogging are some of the most common causes of radiator failure. Any disruption in the radiator’s function can lead to elevated engine temperature and overheating.
Worn/Burst HosesA hose that contains visual cracks or holes, or has burst will result in leaks and disrupt the flow of engine coolant. This can result in overheating.
Bad Radiator FanA fan blows air across the radiator fins to assist in reducing the temperature of the coolant. A fan that wobbles, spins freely when the engine is off, or has broken shrouds will not be able to reduce the temperature to proper level, thus possibly resulting in engine overheating.
Loose or Broken BeltA belt is often the driving link that turns the water pump at the correct speed for proper coolant flow through the cooling system. If a belt is loose or broken, it cannot maintain the proper speed, thus resulting in poor coolant flow and ultimately, engine overheating.
Faulty Water PumpKnown as the ‘heart’ of the cooling system, the water pump is responsible for pressurizing and propelling engine coolant through the cooling system. Any malfunction of the water pump, including eroded impeller vanes, seepage or wobble in the pump shaft, can prevent adequate coolant flow and result in engine overheating.
The internal combustion engine cooling thermostat maintains the temperature of the engine near its optimum operating temperature by regulating the flow of coolant to an air cooled radiator this is its sole purpose
Engine knocking refers to the metallic sound an engine can produce when pressure is applied to the gas pedal. The noise may be a hollow knocking sound or more of a rattling sound—in either case, it's not a sound you want to hear.
When an engine pings, it releases pollution into the environment in the form of nitrogen oxide (NOx) and raw, unburned hydrocarbons (HCs). These two chemicals are poisonous gases that show up as yellowish-brownish in a polluted sky. They can also cause respiratory problems like asthma and emphysema.
Improper Combustion ProcessAn engine can ping (or knock) due to an improper combustion process. A "spark knock" is the result of combustion occurring too early. Early combustion can occur from carbon buildup inside the combustion chamber, a lean air/fuel mixture, and advanced ignition timing (spark plug firing too soon). In a properly-firing cylinder, the spark plug ignites the air/fuel mixture and a flame front starts on one side of the piston and burns across the top to the other side, which creates a rapid and evenly-expanding gas that pushes down on the top of the piston. When the air/fuel mixture is ignited prior to the spark plug firing, the two flame fronts collide, causing the pinging/knocking noise.
Engine Is Too HotAn engine can ping because it is too hot. This is another uneven combustion scenario that is caused by the air-to-fuel mixture "lighting off" by itself. If the cooling system does not keep the engine's combustion chamber temperature in check, the air-to-fuel mixture will begin to spontaneously explode. This is also called "pre-ignition."
Improper Gasoline OctaneIn addition to cooling system problems, pinging can be caused by improper gasoline octane, an overly lean air-to-fuel mixture, or a lack of proper exhaust gas recirculation. The exhaust gas recirculation system (EGR) was created to neutralize engine pinging by adding a small amount of exhaust gas to the air-to-fuel mixture going in to the combustion process, which limits the peak combustion chamber temperature.
Internal Mechanical ProblemsInternal mechanical problems can also cause engine knocking. One such problem stems from excessive clearance inside the bearings in the connecting rods that transfer the downward movement of the pistons to crankshaft rotation. Each time the piston changes direction, there is a knock from the metal hitting metal. This is often referred to as a "rod knock." It is usually very rhythmic—it increases with engine speed and intensifies with engine load.Other mechanical problems that lead to engine knocking are:
The main trouble of overheating is the rupture of the cylinder head gasket.
The thermostat of an engine control the temperature of cooling system in leading more or less cooling fluid to the radiator.
An engine knock, in a gasolene engine, could be caused by trouble in firing system : spark plug, spark cable...
Finally, an oil filter is used to clean your oil and maintain oil with a low part of solid particules.
