Register now or log in to join your professional community.
Pre-tensioning : Pre-tensioning is accomplished by stressing wires or strands, called tendons, to predetermined amount by stretching them between two anchorages prior to placing concretethe concrete is then placed and tendons become bounded to concrete throughout their length. After concrete has hardened, the tendons are released by cutting them at the anchorages. The tendons tend to regain their original length by shortening and in this process transfer through bond a compressive stress to the concrete. The tendons are usually stressed by the use of hydraulic jacks. The stress in tendons is maintained during the placing and curing of concrete by anchoring the ends of the tendons to abutments that may be as much as 200m apart. The abutments and other formwork used in this procedure are called prestressing bench or bed.
In a post-tensioned beam, the tendons are stressed and each end is anchored to the concrete section after the concrete has been cast and has attained sufficient strength to safely withstand the prestressing forcein post-tensioning method, tendons are coated with grease or a bituminous material to prevent them from becoming bonded to concrete. Another method used in preventing the tendons from bonding to the concrete during placing and curing of concrete is to encase the tendon in a flexible metal hose before placing it in the forms. The metal hose is referred to as sheath or duct and remains in the structure.After the tendon has been stressed, the void between the tendon and the sheath is filled with grout. Thus the tendons become bonded to concrete and corrosion of steel is prevented.Post-tension prestressing can be done at site. This procedure may become necessary or desirable in certain cases. For heavy loads and large spans in buildings or bridges, it may be very difficult to transport a member from pre-casting plant to a job site. On the other hand, pre-tensioning can be used in pre-cast as well as in cast-in-place construction.In post-tensioning it is necessary to use some types of device to attach or anchor the ends of the tendons to the concrete section.
To pretension concrete the steel is first tensioned in a frame or between anchorages external to the member. The concrete is then cast around it. After the concrete has developed sufficient strength the tension is slowly released from the frame or anchorage to transfer the stress to the concrete to which the tendons have by that time become bonded. The force is transmitted to the concrete over a certain distance from each end of a member known as the transfer length. Post-tensioned concrete is made by casting concrete that contains ducts through which tendons can be threaded. An alternative is to cast the concrete around tendons that are greased or encased in a plastic sleeve. When the concrete has sufficient strength the tendons are tensioned by means of portable jacks. The load is transmitted to the concrete through permanent anchorages embedded in the concrete at the ends of the tendons. Ducts are usually grouted later or filled with grease to protect the tendons against corrosion. In some applications the post-tensioning tendons are run alongside the concrete member. One advantage of post-tensioning is that it permits using tendons that are curved or draped. (This can be achieved in pretensioning but not so easily.) Post-tensioning can be done on the jobsite without any need of heavy temporary anchorages. Anchorages are needed for each tendon, however, which is a significant cost item.
PRETENSIONING :- Placing of concrete around reinforcing tendons that have been stressed to the desired degree.
POST-TENSIONING :- Reinforcing tendons are stretched by jacks whilst keeping them in serted in voids left pre-hand during curing of concrete.
Pre-tensioning is tensioning prestressed cable before pouring concrete while Post-tensioning is tensioning prestressed cable after pouring concrete. The losses in pre-tension is less than losses in post-tension (there is no friction losses as well as there is no achorage slip losses)
The main difference is, in Pretensioning there have been introduced internal stresses before casting of structural member , whereas in post tensioning the internal stresses induced in the wire after casting of member.
Prestressed concrete is concrete that has had internal stresses introduced to counteract, to the degree desired, the tensile stresses that will be imposed in service. The stress is usually imposed by tendons of individual hard-drawn wires, cables of hard-drawn wires, or bars of high strength alloy steel. Prestressing may be achieved either by pretensioning or by post-tensioning.
Post-tensioned concrete is made by casting concrete that contains ducts through which tendons can be threaded. An alternative is to cast the concrete around tendons that are greased or encased in a plastic sleeve. When the concrete has sufficient strength the tendons are tensioned by means of portable jacks. The load is transmitted to the concrete through permanent anchorages embedded in the concrete at the ends of the tendons. Ducts are usually grouted later or filled with grease to protect the tendons against corrosion.
